Quality Scuba and Snorkeling Equipment from MidCoast Scuba Center - Omaha, Nebraska

[ Home ] [ Up ] [ AIR DELIVERY SYSTEMS ] [ BOUYANCY CONTROL SYSTEMS ] [ PERSONAL DIVE COMPUTERS ] [ CAMERA SYSTEMS ] [ MASKS ] [ FINS ] [ SNORKELS ] [ WET SUITS ] [ ACCESSORIES ]

What to Know Before Purchasing Your Dive Knife

K3 Stainless Knife

This compact stainless steel knife is designed to be worn on the BC and can be used as your primary cutting device or as a backup. Very versatile, it is easy to fasten to most webbing, or on the BC.

• Lanyard opening
• Thumb and index finger support
•  
  • 14.5cm tempered and fined polished stainless blade and handle- Very resistant to corrosion.
  • Compact contoured handle- Easy to grasp with a knurled area for the thumb.
  • Efficient line cutter, screwdriver shaped tip, contoured shackle spanner tool, special serrated edge with 20% more lifetime, fine hollow cutting edge. A complete tool which should never leave you.
  • Includes fastening hardware- Special discs and screws necessary to fasten knife to BC pocket.
  • Rotating bar on the sheath- For easy fastening into the sheath, even with one hand.
  • Eyelets for safety lanyard- One onto the knife, two onto the sheath.

back to top

A Dive Knife is more than just for cutting. It is an essential piece of safety equipment and a valuable multi-purpose Diver's Tool. All divers should have at least one knife and many types of diving conditions require both a larger Primary and smaller Back-up Knife and/or Line Cutter.

We offer a full range of Dive Knives in a variety of blade styles, sizes and mounting options in both Titanium and Stainless Steel construction.

Titanium Knives are lighter, hold a sharp edge exceptionally well and are very low maintenance as they do not rust. Stainless Steel knives are more economical, easier to sharpen and available in a wider variety of styles and price ranges.

Knives with a special "Mono-Cutter" notch are especially effective for quickly slicing through fishing line. Metal end caps can be used for both hammering and signaling (i.e. banging on your tank). Blunt tip knives are much better for prying and digging than sharp points. Plus, since most divers do not (are not able to) look directly at the sheath as they are putting the knife away a blunt tip knife can be easier to manage. Sharp points are better for stabbing (i.e. spearfishing). Sea Scissors and Z-Knives are inexpensive options that are very effective and easy to use. They are a great way to improve in-water safety without excess bulk (or expense).

Wearing Your Dive Knife
Generally, Primary Dive Knives should be worn on the inside opposite leg of your dominant hand. If you are right handed, wear it in on your inside left calf and vice versa if you are left handed. Diver's who use a weight belt should not wear a knife on the outside of their leg. In the event of an emergency weight belt ditch, there is an increased chance of a belt snagging on the knife or knife sheath during the process. Many Weight Integrated Buoyancy Compensators have weight pockets and/or release systems that are extremely unlikely to snag during release. Each should be carefully evaluated on an individual basis before making a decision to wear a knife on the outside of the leg.

Adjust the sheath straps to fit snug keeping in mind that they will loosen slightly at depth as your environmental suit compresses. Once you find the balance between too-tight-on-the-surface and falling-off-in-the-water make a note or mark the notch so you remember for your next dive. Tuck in any excess portion of the strap and/or trim it down. It is a good idea to wear the knife over a course of a few dives before trimming to avoid cutting off too much.

Smaller knives can be mounted almost anywhere on the upper body. It is especially convenient to attach one to your BC (and/or console) and saves time when gearing up. Most Buoyancy Compensators have straps that can be easily laced through a knife sheath. It is a good idea to put your BC on when deciding on the best place to mount your dive knife. Make sure you can easily reach it and that it will not interfere with your other equipment in the water.

Dive Knife Care and Maintenance
It is important that you rinse your knife in fresh water after EVERY Dive! Stainless Steel rusts and even Titanium Knives need the sand, dirt, and salt deposits washed away. If your knife disassembles, remove the end cap and rinse all components thoroughly. Be sure to completely dry your knife before reassembly and storage.

Applying a protective coating is very important. Divers should avoid many common types of lubricants and knife oils because they can actually get on the wetsuit (or dry suit) and deteriorate the material. We recommend Zip Tech for the blade (it lasts longer than sprays and has unique properties to inhibit rust and repel debris without the "gooeyness" of greases and oils) and Silicone Grease for threads and metal locking mechanisms. Apply a thin coating to the entire blade of the knife. If your knife disassembles, coat the threads of the end cap and the metal which sits underneath the grip. Reapply as needed (after a thorough rinsing, cleaning and drying) to continue to provide maximum corrosion resistance.

Back to the top

Contact Information